Installing Starter Shingles On Rake
A simpler and very useful purpose for using starter shingles along the rake edge is that it gives the installer a nice straight line to use as a guide when ending each course of the field shingles. Starter strip plus shingle can extend no greater than 3⁄ 4 beyond the edge of the eave.
It is imperative that you keep the starter row square to the roof.
Installing starter shingles on rake. Install a course (row) of starter shingles along the eaves and rakes with roofing nails according to the manufacturer’s instructions, aligning them correctly with the drip edge on the eaves and rakes. Once the material is up on the roof, they can move on to the starter course. Starter strip plus shingle starter strip plus shingle advantages:
Extend the shingles over the rake and eaves about 1⁄2 (13 mm) if drip edge is used, or about 3⁄4 (19 mm) if no The blade should be facing up. Remember in high wind areas install a leak barrier along the rakes for added protection, and install starter shingles up the rake.
The adhesive strips should be facing upwards. A superior alternative to starter shin. Cut 20 off the first bottom piece.
Then continue across the roof. Place the shingle so that it is flush with the starter course with the start course over hanging the eave or drip edge by 1/4” to 3/4”. Use 5 fasteners for each shingle, placed 2 to 3 inches up from eaves edge.
Tom melillo, residential project manager, roof services: Align starter shingle roll with eave & rake edge granular side up with the seal strip closest to the outer edge of the roof. This product eliminates the need for cutting shingle tabs or inverting them to create a starter row.
Control line and nail them down, four nails per shingle. Apply remaining 131 ⁄4 x 20 piece, followed by full 131 4 x 40 pieces along the eave. (see application instructions on back.) the starter shingle roll advantages:
Start fi rst starter strip plus shingle with 6 removed from the rake edge and fl ush with the drip edge. Easy application application is a snap too. You will completely cover the starter row with roofing shingles and create an 1/8” lip over the rack edge.
You may need to trim the first starter shingle to establish the correct joint stagger with successive courses of shingles. Starter strip plus shingle eliminates the need to cut off tabs or headlap. When laying your shingles, butt them tight against each other as you move down a row.
The starter strip is also required to be secured with 5 fasteners, placed 2 or 3 inches up from the eaves edge. Installation of starter strip shingle starter strip shingle is designed to be broken into two pieces, and each piece has its own sealant strip. Remember, the sealant on starter courses.
If the exposure is greater than 6, a full starter (15½ x 393⁄ 8) would be required. The main reason for a starter course is to fill the gaps between the keys on the shingles. Speeds installation and helps improve safety.
After applying the starter shingles at the eaves, but prior to installing the field shingles, starter shingles may be applied up the slope at the rake edge with sealant facing out and nearest to the outer roof edge. Starter shingle roll along a clean, dry and smooth eave line or rake edge, after removing the release sheet.apply the starter shingle roll directly onto the weatherlock® underlayment or a layer of felt. Place it beneath each shingle against the drip edge;
Choose an outer edge to begin laying your shingles. The shingle manufacturer requires a starter strip to be installed along the eaves. Remove release backer and press to assure full adhesion to the underlayment.
It’s easy for a single person to. Use four nails on these starter shingles as shown on field shingle product wrap. Then, slide the hook knife in your direction and it will score the bottom of the shingle.
Will allow a smooth and uniform transition for applied shingles. For rake application, install drip edge first before applying. Use an owens corning® starter product.
Trim 6 1/2 inches off the rake of the starter course shingle and overhang the drip edge along the rake and eaves edge, 1/4 to 3/4 inch, and continue across the roof. Do not remove the perforated top section. The starter strip on the roof is incorrectly installed.
Without the starter course, water would run. Place the second shingle next to the first. This starter can be used with shingles that have an exposure of no more than 6;
Once it is pressed into place, you’re ready to begin shingling. Place the thermal sealing adhesive toward the eave edge. Lay starter shingles so the top edge butts against the lower edge of the second course of the existing roof.
If no drip edge is used, shingles When separated, each starter shingle is 65⁄ 8 x 393⁄ 8, and each bundle will cover approximately 100 lineal feet. So, when observers look up at the roof gable ends , they’ll see an aesthetically pleasing uniform line rather than ragged and uneven shingle ends.
Shingle installation begins with starter shingles that are installed along the eave and rake edges. This starter can be used with shingles that have an exposure of no more
0 Response to "Installing Starter Shingles On Rake"
Post a Comment