Roofing Starter Strip Application
6.5 if roll roofing is used for the starter strip, nail along a line not greater than 4 inches above the eave line nailing not greater than 12 inches o.c. Accordingly, do you nail down roll roofing?
Use only enough fasteners to hold in place.
Roofing starter strip application. Starter shingles provide multiple purposes along rakes: A new roof is more than just shingles. Before peeling the shingle starter strip, trim about 4 inches off an end of the first starter strip and align the strip to the area you are planning to stick it on.
Not placed over the starter strip joints. Woodstart® starter strip shingles application instructions for use with owens corning ® woodmoor ® or woodcrest ® shingles precautionary note: Check roofing manufacturer’s application instructions and local building codes for their roofing requirements.
Low slope applications (2 to 4 per foot) require additional underlayment. Once it is pressed into place, you're ready to begin shingling. Stagger nail the starter strips using 2 rows of nails spaced 1 (25 mm) and 8 (203 mm) in from roof edge, spaced 4 (102 mm) on center in each row.
The starter course shingles should be cut to match the exposure of the existing first course. Eliminate the need for cutting shingle tabs or inverting them to create a starter row. Apply the starter shingle roll directly onto the weatherlock® underlayment or a layer of felt.
Align this side close to the lowest part of the roof. Simply apply a single course of starter shingle roll along a clean, dry and smooth eave line or rake edge after removing the release sheet. Simply apply a single course of starter shingle roll along a clean, dry and smooth eave line, after removing the release sheet.
Install this starter strip on the lower left corner of the roof deck, granule side up, with the factory installed sealant adjacent to the eaves. The end should overhang over the edge about 1/4 to 3/4 of an inch. Does not provide proper base for shingle application.
Provide extra stability and adhesion to the whole roof. As well, starter shingles have a sealant strip, and, when positioned correctly, the sealant strip will be on the top surface and at the lowest edge of the roof. In areas where icing along the eaves can cause a backup of water, apply certainteed winterguard™ waterproofing shingle
Starter strip shingle application instructions first starter course: Provide superior waterproofing to the whole roof. (a) apply 19 starter strip of underlayment over metal drip edge at eaves.
Why starter strips are so important. Starter strips are one of the most overlooked parts of a quality roofing system! A straight line to properly orient each new row of shingles.
Starter shingles eliminate the need to cut off tabs or headlap. Side laps are to be staggered 6' apart. When separated, each starter shingle is 65⁄ 8 x 393⁄ 8, and each bundle will cover approximately 105 lineal feet.
Install gaf weatherblocker™ starter strip shingles (see figure 1). Requires no special tools, hardware or training Convenient one (1) bundle provides one square of material (105 lineal feet of actual coverage) reduces waste
Place a 9 (229 mm) wide starter strip along eave and rake edges so it overhangs the drip edge 1/4 (6.3 mm). Apply universal starter strips in accordance with local building code requirements and following good roofing practice. Align starter shingle roll with eave & rake edge granular side up with the seal strip closest to the outer edge of the roof.
Use startermatchtm starter strip shingles. Available in handy individual rolls; This starter can be used with shingles that have an exposure of no more
Trim 5 (127 mm) and apply as shown (see figure 2). Application of underlayment, metal drip edges and eaves flashing: Starter shingles should be applied at the rake and continue along the eaves.
You will want the roof granular side up when applying the strip. At the roof’s rake edges, the starter doesn’t necessarily perform that. Thicken the shingle layers sticking over.
Remove release backer and press to assure full adhesion to the underlayment. The manufacturer will not be responsible for problems resulting from any deviation from the recommended application instructions and the following precautions: The starter strip should overhang the rake edge and eaves by.
Installation of starter strip shingle starter strip shingle is designed to be broken into two pieces, and each piece has its own sealant strip. Leaving out the starter strip. If more than one pieceof rollroofingmustbeused, the end joint shall be butted.
0 Response to "Roofing Starter Strip Application"
Post a Comment